Skip to content
Assessment
LibrarySustainability

Where does the farm's energy go, month by month?

Put every energy bill on one sheet, convert them to one unit, split the electricity by job and check what the panels make against the bill. Do it before you buy.

Published Updated 15 min read
In this article

In the worked example of a Purdue Extension guide to dairy farm energy audits, one farm paid $39,491 for electricity in a year and $62,679 for diesel. Electricity was 31 percent of the $127,688 the farm spent on energy, and diesel was 49 percent. A farmer who watches only the electric bill watches less than a third of the money and a sixth of the energy the farm buys. The next decision is what to buy: panels, a new motor, a tank. A farmer who decides from the electric bill alone aims at the wrong target.

Put twelve months of every energy bill on one sheet, convert them to one unit, split the electricity by job, and compare what the panels make with what the bill shows. Do that before you buy anything.

Which bills go on the sheet, and for how many months?

Every energy source the farm buys gets its own column: grid electricity, diesel, propane or natural gas, and any wood or gasoline. The Ontario Soil and Crop Improvement Association sets the minimum for a detailed farm energy audit. The auditor must review at least 12 months of utility bills to quantify consumption of electricity, natural gas, diesel, propane and other energy sources.

Twelve months is the unit because each load (each machine that uses energy) follows its own season, and a shorter sheet leaves some of them out. Purdue’s guide asks for the same record before an audit visit: the usage and costs of the prior year’s energy, listed by resource. It adds that checking the results of any change afterwards takes a year of data.

Diesel is the column easiest to forget, because it arrives as delivery tickets and card receipts, not as a monthly statement. Enter each delivery in the month it arrived. If you read the tank, a balance of what it held, what came in and what is left, as in the check of fuel bought against hours worked, turns deliveries into gallons used.

If the farm has panels, add two more columns. One is the kilowatt-hours the panels made, which the inverter app shows (the inverter is the box that turns panel output into grid power and logs it). The other is the kilowatt-hours sent to the grid, which the electric bill shows.

Figure: The eight columns of the monthly sheet and where each number comes from. Source: layout proposed in this article; the audit guides of Purdue and Ontario ask for the same bills
Eight columns, one row for each monthMonth, grid kilowatt-hours and cost from the electric bill, diesel gallons and cost from invoices, other fuels, panel kilowatt-hours made from the inverter app, and kilowatt-hours sent to the grid from the electric bill.One row for each month, 12 rowsColumnWhere it comes fromMonth usedthe calendarGrid kWhelectric billGrid costelectric billDiesel gallonsinvoices, tankDiesel costinvoicesOther fuelspropane, gas, woodPanel kWh madeinverter appkWh sent to gridelectric bill

How do I compare a kilowatt-hour with a gallon of diesel?

Convert electricity and diesel to one common unit, a million British thermal units, written MMBtu, a measure of heat. One kilowatt-hour is 3,412 British thermal units, so one MMBtu is about 293 kilowatt-hours. Purdue’s audit procedure follows these steps. The auditor summarizes the bills into an average cost per kilowatt-hour and per gallon, converts each to dollars per MMBtu, and adjusts for the efficiency of the machines each fuel feeds.

The guide’s worked example shows what that does to the picture.

Figure: Share of the farm's money and of the energy it bought that went to electricity and to diesel, in the Purdue worked example. Source: the calculation in the text on Figure 1 of Purdue Extension RE-12-W
Electricity is 31 percent of the money but 16 percent of the energy boughtOf the money spent, electricity took 31 percent and diesel 49 percent. Of the energy bought in MMBtu, electricity was 16 percent and diesel 51 percent.Electricity and diesel, one year31%49%16%51%Elec.DieselElec.DieselMoney spentEnergy bought

Read these numbers three ways. In money, diesel is the bigger line and electricity the second. In energy bought, diesel is half the farm and electricity a sixth. Per unit of energy, electricity costs twice what diesel does, which is why a third of the money buys a sixth of the energy.

The last reading, useful energy, is for judging what a swap would save, and it rests on efficiencies that the guide assumes for the engines. Start with the first two. They need no assumption, and they decide which column deserves the next hour.

A second sample also puts diesel near half of the energy, with a much larger electric share. Uruguay’s Ministry of Industry, Energy and Mining built a manual on energy audits of 103 dairy farms. On those farms, electricity was 50 percent of consumption and diesel 48 percent, 98 percent together. Both samples are dairy farms. A grain farm with a dryer or center-pivot irrigation may split differently, and the sheet is how it finds out.

Where does the electricity go inside the farm?

The bill gives one number for the whole farm. The Ontario requirements ask for more: a baseline for the farm’s major activities (their use before any change), using measured data wherever possible, which can include sub-metering or spot measurements. A sub-meter is a second meter on one circuit. A spot measurement is a reading of one machine’s power at one moment, taken with a clamp meter, a hand tool that reads the current in a wire.

Few jobs carry most of the bill. On the 103 Uruguayan dairy farms, milk cooling took 40 percent of the electricity and the milking vacuum pump 30 percent. Water pumping took 15 percent, and hot water, lighting and motors took 5 percent each. List the two or three biggest loads on your farm and measure those first.

Without a sub-meter, estimate each load as its power in kilowatts times the hours it runs in the year, then add the loads and compare the total with the 12 months of bills. On a second tab of the sheet, each load gets a row: its power, the hours of each month and the kWh. Count the hours month by month for a load that follows the season, such as grain drying or irrigation. A load that runs all year, such as the milk tank, can use its daily hours times the days. The estimate costs nothing, but it rests on the nameplate power, and a motor can draw less or more than its plate says. A clamp reading on the two biggest loads replaces that guess with a measurement.

Figure: The four loads added up against the 12 months of bills on the example dairy. Source: the calculation in the text; the loads and the bill are invented for the example
The four loads explain 23,506 of 30,000 kilowatt-hoursThe estimated loads add to 23,506 kilowatt-hours. The 12 bills show 30,000. The difference, 6,494 kilowatt-hours or 22 percent, is not explained.Kilowatt-hours in the year23,50630,0006,494Loads addedkW x hours12 bills22% not explained

Write the leftover as its own line, not explained, and leave it there. Spreading it across the loads makes the sheet look closed and hides the question. A large leftover means a load is missing from the list, usually one that runs when nobody is looking. A house, a shop or a pump for a neighbor on the same meter belongs here too. For the family home on a dairy’s meter, the Uruguayan manual advises estimating its use and taking it out, or keeping the same method before and after any efficiency measure so the comparison holds.

How do I check what the panels make against the bill?

Panels make the bill smaller, and a smaller bill hides how much the farm uses. The farm’s total use is the kilowatt-hours bought from the grid, plus the kilowatt-hours the panels made, minus the kilowatt-hours sent to the grid. Find the first and the last on the electric bill and the middle one in the inverter app. Do the sum for each month, because the array’s output follows the sun and the farm’s load follows the herd and the crop.

Figure: Kilowatt-hours the bill shows and kilowatt-hours the example dairy used in the year. Source: the calculation in the text; the readings are invented for the example
The bill shows 120,000 kilowatt-hours, the farm used 145,000The bill shows 120,000 kilowatt-hours bought. Adding the 25,000 used straight from the panels gives a total use of 145,000.Kilowatt-hours in the year120,000145,000Billbought from gridTotal use+25,000 from panels

The array made 45,000 kilowatt-hours, which is 38 percent of the 120,000 on the bill, the ratio that is easiest to compute. Measured against the 145,000 the farm used, the panels fed the farm directly 17 percent of its use. The other 20,000 went to the utility, and what the utility pays or credits for it depends on the local rule. Ask the utility whether it charges a minimum even to a customer who sends back more than they draw. Read the terms on your own bill before you count that energy as saved.

Whether the panels pay for themselves is a different calculation, with its own method in the article on payback, net present value and your rate. It needs this sheet’s total use as its input, and anyone who starts from a bill that hides the panels’ share ends with the wrong one.

What do I write first, and by when?

This week, download the last 12 monthly electric statements and the diesel invoices, and fill the first columns. Read two numbers from them: the biggest source in dollars and the biggest source in MMBtu. Where the two disagree, you have found the bill you were not watching. The Purdue example agrees on diesel for both, but look at the second place too: electricity is second in dollars and third in MMBtu, behind propane.

Next month, add the loads by kilowatts times hours and the panel columns. Then close each month: write the gap between what you expected and the numbers on the sheet, who looks into it and by when. Pick the date of the first close today, before you open the first statement. A gap that nobody owns and nobody dated stays open from one year to the next.

Figure: The order of the five steps, from the first week to each month. Source: order proposed in this article
Five steps, from twelve bills to a monthly closeFirst load 12 months of bills, then read the biggest source in dollars and in MMBtu, then list the loads as kilowatts times hours, then check the panels against the bill, and close each month writing the gap.Do in this order1Load 12 months of bills2Biggest source: dollars, MMBtu3List the loads: kW x hours4Check the panels against the bill5Close each month, write the gap

The same columns serve two other questions. The diesel gallons are the fuel figures that the farm’s carbon count multiplies by published factors. And when a lender or a buyer asks for energy numbers, the sheet has them; the article on whether a farm needs an ESG report covers what a lender checks besides. The sheet is one of the counts of running a farm business, and the sustainability library lists the neighboring ones.

Provenance

Derives from
  1. Martin and Ileleji, A Stepwise Guide to Prepare for Dairy Farm Energy Audit, Purdue Extension RE-12-W
  2. Ontario Soil and Crop Improvement Association, Detailed Energy Audit (Level 2) Minimum Requirements, 2026
  3. MIEM and INALE, Oportunidades de Eficiencia Energética en Tambos: Manual de buenas prácticas, Uruguay, 2025
What this article covers
A monthly sheet of the energy a farm buys and makes, by source (grid, diesel, other fuels, own generation), the electricity split by job, and the difference between what the panels make and what the bill shows.
What it does not cover
Which energy system to choose or whether solar pays off, the check of fuel bought against tractor hours, and the farm's emissions. Each has its own article.
Published
Updated
Error found
Point out an error and the article is corrected with a note on what changed.

How to cite this article

Rurivia. (2026, October 28). Where does the farm's energy go, month by month? https://rurivia.com/en/library/sustainability/where-the-farms-energy-goes-month-by-month/


Keep reading

Sustainability

What does the farm own in the co-op, and did it vote?

A co-op membership brings a store discount, capital the farm owns inside the cooperative, and a vote. Most farms can describe only the discount. One page, one row per membership, holds the other two.

Aug 27, 2026
Sustainability

Who may use the data when a company runs a trial on your farm?

Before a company, an institute or a university runs a trial on your farm, both sides can sign a one-page trial agreement with six items. The first item says who may use the data from the strip of your field where the trial runs, a question that few laws answer.

Aug 27, 2026
Sustainability

Farm code of conduct: set consequences before a case

A written code alone changes little. On the day a rule is broken or someone is harassed, a consequence decided beforehand and a complaint route that skips the boss are what you can point to.

Sep 5, 2026
Sustainability

Log what your farm gives the community, and who approves

Grader hours, a steer, diesel and a worker's paid time left one farm in a single March. Each was decided by whoever picked up the phone, and none was written down as a gift.

Aug 27, 2026

Farm Management

If this article were a plant, farm management would be the whole field.

Planning, organizing, leading and controlling: the four functions, what each one decides, and a farm example for each, all on one page.